ISO 527-3:1995 download

07-16-2021 comment

ISO 527-3:1995 download.Plastics — Determination of tensile properties — Part 3: Test conditions for films and sheets.
1,1 This part of ISO 527 specifies the conditions for JeIerrnining the ten5lle propertie3 of plttc films or sheets less than 1 mm thick, based upon the general principles given 10 part 1.
NOTF 1 For sheets greater than 1 mm thick, the user is referred to part 2 ol this Iriteindliunul SLdlwJaid.
1.2 See ISO 527-1. subclause 1.2.
1.3 This part of ISO 527 is not normally suitable tor determining the tensile properties of
a) cellular materials;
b) plastics reinforced by textilc fibres.
1.4 See ISO 527-1, subclause 1.5.
2 Normative references
The following standards contain provisions which. through reference in this text, constitute provisions of this part of ISO 527. At the time of publication, the editions indicated were valid. All standards are subject to revision, and parties to agreements based on this part of ISO 527 are encouraged to investigate the possibility of applying the most recent editions of the standards indicated below. Members of IEC and ISO maintain registers of currently valid International Standards.
ISO 5271:1993, Plastics — Determination of tensile properties — Part 1; Cencral principles.
ISO 4591:1992, Plastics — Film and sheeting — Determination of average thickness of a sample, and average thickness and yield of a roll, by gravimetric techniques gravimtric thicknss)
ISO 4593:1993, Pldslivs — Film dncJ hetir,q — Dete ,ininution of thickness by mechanical scanniny.
3 Principle
See ISO 527-1. clause 3
4 Definitions
See ISO 527-1, clause 4.
5 Apparatus
See ISO 527-1. clause 5. subject to the following adciitional requirements.
In 5.1.2. the tensile-testing machine shall be capable of maintaining the speeds of testing as specified in table 1 of ISO 527-1 It is normal for films and sheets to be tested at a sped of 5 mmlmin. 50 mm/mm. 100 mmjmin. 200 mmImin, 3(M) mmlmin or
500 mm/mm. The information contained in ISO 5)1-1. subclause 9.6. also applies.
In 5.1 .5. when testing thin sheets or film material, the sDeclmen shall riul cdiiy L[ie weight uf the exter isuineter.
In 5.2, devices complyinO with the requirements in ISO 4593 shall be used for measuring the thickness. except in the case of very thin film (less than 0.01 mm thick) or embossed film. In those cases, the thickness shall be determined by the method specified in ISO 4591. When (SO 4591 is used, the aveidge thickness of the film sample shall be taken as the thickness of the test specimen.
6 Test specimens
6.1 Shape and dimensions
6.11 The preferred form of test specimen for the determination of tensile properties by this method is a strip 10 mm to 25 mm wide and not less than 150 mm long (specimen type 2 — sets fiquic 1), having two parallel gauge marks, 50 mm apart, on the ceritrl portion of the 5pecimen.
Some film materials have a very high elongation at break which may result in them being outside the stretching capacity of the testing machine In such cases. it is permissible to reduce the initial distance between the qrip w 50 nun.
6.1.2 When required by the specification for the material under test or for routine quality-control tests, dumb-bell specimen types 5, 1 B and 4 of the shape and dimensions shown in figures 2. 3 and 4 may be used. These specimens are convenient to produce and permit rapid quality-control testing
Specimen type 5 (figure 2) is recommended for film and sheet with a vory high straan at break. Spccimcn type 4 is recommended for other types of flexible thermoplastic sheet.
Specimen type 18 (figure 3) is recommended for rigid sheets.

Download infomation Go to download
Note: If you can share this website on your Facebook,Twitter or others,I will share more.

ISO 9885:1991 download free

ISO 9885:1991 download free.Wide-mouth glass containers - Deviation from flatness of top sealing surface - Test methods. ISO 9885 specifies two complementary test methods for the determination or the deviation from flatness of the top sealing surface...
Download Now

ISO 9009:1991 download

ISO 9009:1991 download.Glass containers — Height and non-parallelism of finish with reference to container base — Test methods. ISO 9009 specifies test methods for determining the height and the non-parallelism of finish with reference to the container...
Download Now

ISO 10076:1991 pdf free download

ISO 10076:1991 pdf free download.Metallic powders — Determination of particle size distribution by gravitational sedimentation in a liquid and attenuation measurement. The settling behaviour under gravity of a given mass of particles dispersed in an initially static...
Download Now


Anonymous netizen Fill in information