BS EN ISO 4762:1998 download

07-10-2021 comment

BS EN ISO 4762:1998 download.Hexagon socket head cap screws.
BS EN ISO 4762 specifies the characteristics of hexagon socket head cap screws with threads from M1,6 up to and including M64 and product grade A.
Gauging of hexagon sockets is specified in Annex A. For approximate masses of screws see Annex B.
If, in special cases, specifications other than those listed in BS EN ISO 4762 are required, they should be selected from existing International Standards, for example ISO 261, ISO 888, ISO 898-1, Iso 965-2, Iso 3506-1 and ISO 4759-1.
2 Normative references
The following standards contain provisions which, through reference in this text, constitute provisions of BS EN ISO 4762. At the time of publication, the editions indicated were valid. All standards are subject to revision, and parties to agreements based on BS EN ISO 4762 are encouraged to investigate the possibility of applying the most recent editions of the standards indicated below Members of IEC and ISO maintain registers of currently valid International Standards. ISO 225:1983, Fasteners — Bolts, screws, studs and nuts — Symbols and designations of dimensions.
ISO 261:—, ISO general ,urpose metric screw threads — General plan’.
ISO 888:1976, Bolts, screws and studs — Nominal lengths, and thread lengths for general purpose bolts.
ISO 898-1:—, Mechanical properties of fasteners made of carbon and alloy steel — Part 1: Bolts, screws and studs2.
Iso 965-2:—-, ISO general purpose metric screw threads — Tolerances — Part 2: Limits of sizes for generalpurpose bolt and nut threads — Medium quality”.
Iso 965-3:—, ISO general purpose metric screw threads — Tolerances — Part 3: Deviations for constructional threads4.
ISO 3269:1988. Fasteners — Acceptance inspection. ISO 3506-1:1997, Mechanical properties of corrosion-resistant stainless steel fasteners — Part 1: Bolts, screws and studs.
ISO 4042:—, Fasteners — Electroplated coatings5. Iso 4753:1983, Fasteners — Ends of parts with external metric ISO threads.
ISO 4759-1:—, Tolerances for fasteners — Part 1: Bolts, screws, studs and nuts — Product grades A, B and £.
ISO 6157-1:1988, Fasteners — Surface discontinuities — Part 1: Bolts, screws and studs for general requirements.
ISO 6157-3:1988, Fasteners — Surface discontinuities — Part 3: Bolts, screws and studs for special requirements.
ISO 8839:1986. Mechanical properties of fasteners — Bolts, screws, studs and nuts made of non-ferrous metals.
ISO 8992:1986. Fasteners — General requirements for bolts, screws, studs and nuts.
3 Dimensions
See Figure 1 and Table 1.
Symbols and designations of symbols are defined in ISO 225.

Download infomation Go to download
Note: If you can share this website on your Facebook,Twitter or others,I will share more.

ISO 9885:1991 download free

ISO 9885:1991 download free.Wide-mouth glass containers - Deviation from flatness of top sealing surface - Test methods. ISO 9885 specifies two complementary test methods for the determination or the deviation from flatness of the top sealing surface...
Download Now

ISO 9009:1991 download

ISO 9009:1991 download.Glass containers — Height and non-parallelism of finish with reference to container base — Test methods. ISO 9009 specifies test methods for determining the height and the non-parallelism of finish with reference to the container...
Download Now

ISO 10076:1991 pdf free download

ISO 10076:1991 pdf free download.Metallic powders — Determination of particle size distribution by gravitational sedimentation in a liquid and attenuation measurement. The settling behaviour under gravity of a given mass of particles dispersed in an initially static...
Download Now


Anonymous netizen Fill in information